{"id":25826,"date":"2018-04-15T23:29:01","date_gmt":"2018-04-16T03:29:01","guid":{"rendered":"https:\/\/www.raytownproductions.com\/blog\/?p=25826"},"modified":"2026-11-11T00:24:06","modified_gmt":"2026-11-11T05:24:06","slug":"8-tips-to-get-the-most-from-online-song-mastering","status":"publish","type":"post","link":"https:\/\/www.raytownproductions.com\/blog\/8-tips-to-get-the-most-from-online-song-mastering\/","title":{"rendered":"How to Prepare Your Mix for Online Mastering: 8 Tips to Get the Most From Your Mastering Engineer"},"content":{"rendered":"\n<div class=\"wp-block-group rytbd-summary is-layout-flow wp-block-group-is-layout-flow\">\n<h2 class=\"wp-block-heading\">Quick summary<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">To get the most from online mastering, send your mastering engineer a clean, finished stereo mix with room to work. Bypass limiters, loudness plugins and dither on the master bus, and keep other master bus processing only if it is a necessary part of the sound. Make sure the mix never goes over 0 dBFS; peaks around &#8722;6 dBFS are a comfortable starting point. Fix clicks, pops and unwanted noise in the mix first. Export an uncompressed WAV or AIFF at the sample rate and bit depth you recorded at, name each file with its two-digit track number and final song title, and include a track info sheet, reference songs and notes. All eight tips are explained below.<\/p>\n<\/div>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-note rytbd-updated is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Updated <time datetime=\"2026-11-11\">November 11, 2026<\/time>:<\/strong> completely rewritten and expanded with a one-page checklist, new diagrams, an export settings table, a section on revisions and what you get back, and FAQs. Originally published April 15, 2018.<\/p>\n<\/div>\n\n\n\n<div class=\"wp-block-group rytbd-toc is-layout-flow wp-block-group-is-layout-flow\">\n<h2 class=\"wp-block-heading\">What&#8217;s In This Article<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"#what-a-mastering-engineer-needs\">What Does an Online Mastering Engineer Need From You?<\/a><\/li>\n\n\n\n<li><a href=\"#is-your-mix-finished\">Is Your Mix Really Finished?<\/a><\/li>\n\n\n\n<li><a href=\"#master-bus-before-mastering\">What Should I Turn Off on the Master Bus Before Mastering?<\/a><\/li>\n\n\n\n<li><a href=\"#headroom-for-mastering\">How Much Headroom Should I Leave for Mastering?<\/a><\/li>\n\n\n\n<li><a href=\"#export-settings-for-mastering\">What File Format, Bit Depth and Sample Rate Should I Export?<\/a><\/li>\n\n\n\n<li><a href=\"#name-and-organize-files\">How Should I Name and Organize My Files?<\/a><\/li>\n\n\n\n<li><a href=\"#track-info-sheet-references-notes\">What Information Should I Send With the Mix?<\/a><\/li>\n\n\n\n<li><a href=\"#revisions-and-what-you-get-back\">What Happens After You Send Your Mix?<\/a><\/li>\n\n\n\n<li><a href=\"#closing-thoughts\">Closing Thoughts<\/a><\/li>\n<\/ul>\n<\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Mastering is the final step before you release your music, after all the hard work of writing, recording and mixing. So it&#8217;s very important to set your mastering engineer up for success. I&#8217;ve been mixing and mastering for more than twenty years, and the same avoidable mistakes show up in the files people send me again and again.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This article covers the 8 most important rules for getting your mix exported and delivered correctly. It&#8217;s about preparing and sending a finished stereo mix, and working with the engineer once it&#8217;s sent. If you want to know what mastering is in the first place, start with <a href=\"https:\/\/www.raytownproductions.com\/blog\/what-is-mastering-and-why-you-need-it\/\">what mastering is and why you need it<\/a>.<\/p>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-warning is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Don&#8217;t expect miracles from mastering.<\/strong> Mastering brings out all the details of the recording, both good and bad. It makes good mixes sound incredible, but a bad mix may not benefit from mastering at all.<\/p>\n<\/div>\n\n\n\n<h2 id=\"what-a-mastering-engineer-needs\" class=\"wp-block-heading\">What Does an Online Mastering Engineer Need From You?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For a normal mastering job, I need <strong>one stereo file per song<\/strong>: your final mix, exactly as you approved it, minus the processing that only made it louder. I don&#8217;t need your multitracks. Everything I do in mastering affects the whole song at once, so the mix has to arrive with the balance you want and with enough room left for me to shape tone, dynamics and loudness.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Here are the 8 tips on one page. Work through them from the top before you upload anything. Each one is explained in the sections that follow.<\/p>\n\n\n\n<figure class=\"wp-block-table is-style-stripes rytbd-table\"><table><thead><tr><th><\/th><th>Tip<\/th><th>What to check<\/th><\/tr><\/thead><tbody><tr><td>&#9744;<\/td><td>1. Remove dynamics processing from the main output bus<\/td><td>Compressors and limiters are bypassed, unless the processing is a necessary part of the sound.<\/td><\/tr><tr><td>&#9744;<\/td><td>2. Bypass all dithering<\/td><td>Dither is off in the export window and inside any plugin that has its own dither option.<\/td><\/tr><tr><td>&#9744;<\/td><td>3. Keep the output below 0 dBFS<\/td><td>The master meter never goes into the red. Peaks around &#8722;6 dBFS are a comfortable starting point.<\/td><\/tr><tr><td>&#9744;<\/td><td>4. Listen for pops and clicks<\/td><td>Every edit is crossfaded. Anything you hear is fixed in the mix session.<\/td><\/tr><tr><td>&#9744;<\/td><td>5. Remove unwanted noise<\/td><td>No talking, headphone bleed, floor creaks or count-ins that aren&#8217;t meant to be in the song.<\/td><\/tr><tr><td>&#9744;<\/td><td>6. Label your songs correctly and neatly<\/td><td>Each file starts with a two-digit track number, followed by the full, final song title.<\/td><\/tr><tr><td>&#9744;<\/td><td>7. Include a track info sheet<\/td><td>Artist, titles, running order and any metadata you want encoded in the final files.<\/td><\/tr><tr><td>&#9744;<\/td><td>8. Export an uncompressed audio format<\/td><td>WAV or AIFF at the sample rate and bit depth you recorded at. No MP3s.<\/td><\/tr><\/tbody><\/table><figcaption class=\"wp-element-caption\">The online mastering prep checklist: tick every box before you send your mix.<\/figcaption><\/figure>\n\n\n\n<h2 id=\"is-your-mix-finished\" class=\"wp-block-heading\">Is Your Mix Really Finished?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Before you think about export settings, make sure the mix itself is done. An online mastering engineer can&#8217;t lean over and ask you whether something is supposed to be there, and most problems are far easier to fix in the mix session than in a stereo file.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Listen for pops and clicks, and edit them out.<\/strong> Audible clicks and pops are usually caused by bad editing, particularly where audio clips were not properly crossfaded. Listening to the individual tracks in solo (especially vocals) makes the bad edits easier to hear. If you hear a click or pop:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>First, look for a bad crossfade at that spot and fix it.<\/li>\n\n\n\n<li>If there is no edit there and the click is still audible, copy an identical section of the performance and paste it over the problem. Crossfade those clips too!<\/li>\n\n\n\n<li>If that isn&#8217;t possible, try re-recording the part.<\/li>\n\n\n\n<li>As a last resort, a mastering engineer should be equipped with tools to try to repair the audio, but don&#8217;t count on it.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Remove unwanted noise.<\/strong> Talking, headphone bleed between vocal parts, floor creaks, amp buzz and unwanted count-ins all fall into this group. I don&#8217;t know whether a buzzing guitar or a four-count on the hi-hat before the song is supposed to stay in or not. It&#8217;s safe to say that if you don&#8217;t want something in the song, remove it before you send it out for mastering.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This matters more than you&#8217;d think. In a song with many tracks, small noises build up, and mastering brings the smallest details of a recording to the front. A noise you could barely hear in the mix can be obvious after the song has been made louder.<\/p>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-tip is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Listen to the exported file, not the session.<\/strong> After you bounce the mix, play the actual file from start to finish on headphones. That is the only way to catch a clipped first note, a muted track, a plugin that didn&#8217;t render or a reverb tail that got cut off. For the mix itself, I have a separate <a href=\"https:\/\/www.raytownproductions.com\/blog\/final-mix-checklist-pro-uses\/\">final mix checklist<\/a> you can run through first.<\/p>\n<\/div>\n\n\n\n<h2 id=\"master-bus-before-mastering\" class=\"wp-block-heading\">What Should I Turn Off on the Master Bus Before Mastering?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Remove any dynamics processing on the main output bus.<\/strong> The mastering engineer needs flexibility when it comes to controlling the movement and dynamics of the song. A compressor or limiter on the stereo bus reduces the dynamic range, and once the dynamic range is reduced, it is very difficult, if not impossible, to bring back. So bypass any compressors and limiters on the main stereo bus, along with maximizers and any clipper you added only to make the mix louder.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">There is one exception. <strong>If the compression, EQ or effect is an absolutely necessary part of the sound, leave it on.<\/strong> A bus compressor you mixed into from the start is a good example: the balance of the whole mix was built around it, and taking it off changes the mix. In all other cases, let the mastering engineer balance the song sonically and decide how loud to make it.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass.webp\" alt=\"Diagram of a master bus insert chain showing EQ, bus compressor and saturation marked bypass unless part of the sound, clipper and limiter marked bypass, dither marked off, plus export window settings with normalize and dither turned off\" class=\"wp-image-29578\" width=\"1600\" height=\"900\" srcset=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass.webp 1600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass-600x338.webp 600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass-1024x576.webp 1024w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass-768x432.webp 768w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass-1536x864.webp 1536w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-master-bus-what-to-bypass-1080x608.webp 1080w\" sizes=\"(max-width: 1600px) 100vw, 1600px\" \/><figcaption class=\"wp-element-caption\">Bypass anything that only adds loudness. Keep master bus processing only when the mix was built around it.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">If you aren&#8217;t sure which side of the line a plugin falls on, my <a href=\"https:\/\/www.raytownproductions.com\/#faq\">services FAQ<\/a> has the easy answer: send two versions, one with the master bus effects and one without. Label them clearly and I&#8217;ll use whichever gives the better master.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Bypass all dithering.<\/strong> Dither is a very small amount of noise that is added when audio is reduced to a lower bit depth, for example from 24-bit to 16-bit. The noise covers up the more noticeable artifacts that the conversion would otherwise cause. It&#8217;s meant to be applied once, at the very end. If you dither the mix and the mastering engineer then processes it and dithers again, you&#8217;ve added noise for no benefit.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Dithering usually isn&#8217;t necessary as long as you export the audio in the same format it was recorded in. A good rule of thumb is to save the dithering for the mastering engineer, who will dither correctly for the playback medium. Check two places:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>The export window.<\/strong> Some DAWs turn dither on for you. In Ableton Live, for example, the <a href=\"https:\/\/www.ableton.com\/en\/manual\/managing-files-and-sets\/\" target=\"_blank\" rel=\"noreferrer noopener\">manual<\/a> says Triangular dither is selected by default when you render below 32-bit. Set it to No Dither.<\/li>\n\n\n\n<li><strong>Your plugins.<\/strong> Dither is often built into limiters. The Waves L2 is one example: it has its own dither and noise-shaping section. If you leave a plugin like that on for any reason, turn its dither off. When in doubt, read the plugin&#8217;s manual and see what the manufacturer recommends.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">If you want to understand what dither actually does, I explain it in plain language in <a href=\"https:\/\/www.raytownproductions.com\/blog\/wtf-is-dither-audio-dithering-guide\/\">WTF is dither?<\/a>.<\/p>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-tip is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Make a reference before you bypass everything.<\/strong> If you&#8217;ve been listening to the mix through a clipper and limiter, export that version too and add &#8220;-Reference&#8221; to the file name. It&#8217;s the best sound you got with your own master bus processing, and it shows your mastering engineer the loudness and feel you&#8217;ve gotten used to. If you don&#8217;t own a clipper, the Basic version of my own, <a href=\"https:\/\/www.raytownproductions.com\/plugins\/hardstop\/\">HardStop<\/a>, is free. Then bypass the loudness plugins and export the file that will actually be mastered.<\/p>\n<\/div>\n\n\n\n<h2 id=\"headroom-for-mastering\" class=\"wp-block-heading\">How Much Headroom Should I Leave for Mastering?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Make sure the output volume does not exceed 0 dBFS. It should never be in the red.<\/strong> 0 dBFS is the ceiling of a digital file. Anything that tries to go above it gets clipped off, and that distortion is baked into the file for good.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When multiple audio tracks are summed together during the mix export, the total can clip even though no individual track does. So watch the master meter through the loudest section of the song, not just the channel meters.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix.webp\" alt=\"Two waveforms compared: a mix exported through a limiter with peaks pinned at 0 dBFS, and the same mix with the limiter bypassed and peaks around -6 dBFS, leaving headroom for mastering\" class=\"wp-image-29579\" width=\"1600\" height=\"900\" srcset=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix.webp 1600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix-600x338.webp 600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix-1024x576.webp 1024w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix-768x432.webp 768w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix-1536x864.webp 1536w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-mix-headroom-vs-limited-mix-1080x608.webp 1080w\" sizes=\"(max-width: 1600px) 100vw, 1600px\" \/><figcaption class=\"wp-element-caption\">Illustration: a mix bounced through a limiter has nothing left to work with. The same mix with the limiter bypassed and peaks around &#8722;6 dBFS gives the mastering engineer room.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">How much room should you leave? For songs sent to me, I ask for <strong>at least &#8722;3 dBFS of headroom, and &#8722;6 dBFS is better<\/strong>. With the loudness plugins bypassed, the simplest way to get there is to lower the master bus fader until the loudest part of the song peaks around &#8722;6 dBFS. That avoids accidentally clipping the audio during export.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>It&#8217;s a starting point, not a target.<\/strong> A mix that peaks at &#8722;4 or &#8722;8 dBFS is just as usable. What matters is that nothing clips and no limiter is flattening the peaks.<\/li>\n\n\n\n<li><strong>If you kept a bus compressor,<\/strong> check that lowering the fader doesn&#8217;t change how hard the compressor is being hit. In some DAWs the master fader comes before the master inserts. If that&#8217;s the case in yours, turn the level down after the compressor instead.<\/li>\n\n\n\n<li><strong>Turn off normalization.<\/strong> A normalize option in the export window raises the file until its highest peak sits at the top, which removes the headroom you just left.<\/li>\n\n\n\n<li><strong>Don&#8217;t rely on 32-bit float to save you.<\/strong> A 32-bit float file can store peaks above 0 dBFS without clipping them, but it&#8217;s still good practice to check the meter and keep the mix out of the red.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">A quieter mix file does not mean a quieter master. Loudness is set in mastering, and my goal there is to make the song as loud as it can go while it keeps the punch and depth it needs.<\/p>\n\n\n<div class=\"rpo rpo-inline\" id=\"rpo-optin_10-1\" data-rpo-form=\"optin_10\" data-rpo-rest=\"https:\/\/www.raytownproductions.com\/blog\/wp-json\/rpo\/v1\/\" data-rpo-ts=\"0x4AAAAAAF6v0pb5pNfz87oP\"><img class=\"rpo-image\" src=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2021\/02\/Free-Plugins-Book-Mock-Up.jpg\" alt=\"\" width=\"1500\" height=\"1383\" loading=\"lazy\" decoding=\"async\"><div class=\"rpo-body\"><div class=\"rpo-title\" id=\"rpo-optin_10-1-t\"><h2><span>Grab All My Favorite FREE Plugins!\u00a0<br \/><\/span><\/h2><\/div><div class=\"rpo-message\"><p><span>This FREE guide contains everything you need to make PRO sounding music in your home studio.<br \/><br \/><\/span><span>\ud83d\udca5 EQs<\/span><br \/>\ud83d\udca5<span>\u00a0Compressors<\/span><br \/>\ud83d\udca5<span>\u00a0Drum Samples\/Players<\/span><br \/>\ud83d\udca5<span>\u00a0Guitar Sims<\/span><br \/>\ud83d\udca5<span>\u00a0Impulse Loaders<\/span><br \/>\ud83d\udca5<span>\u00a0Clippers\/Limiters<\/span><br \/>\ud83d\udca5<span>\u00a0Saturation\/Distortion<br \/>\ud83d\udca5\u00a0Cinematic Effects and Impacts<br \/>\ud83d\udca5\u00a0AND MORE!<br \/><\/span><\/p><\/div><form class=\"rpo-form\" method=\"post\" action=\"#\" novalidate><div class=\"rpo-field\"><label class=\"rpo-sr\" for=\"rpo-optin_10-1-e\">Email<\/label><input type=\"email\" id=\"rpo-optin_10-1-e\" name=\"email\" placeholder=\"Email\" autocomplete=\"email\" inputmode=\"email\" autocapitalize=\"off\" spellcheck=\"false\" required><\/div><div class=\"rpo-hp\" aria-hidden=\"true\"><label for=\"rpo-optin_10-1-w\">Website<\/label><input type=\"text\" id=\"rpo-optin_10-1-w\" name=\"website\" tabindex=\"-1\" autocomplete=\"off\"><\/div><button type=\"submit\" class=\"rpo-btn\">GET FREE GUIDE!<\/button><div class=\"rpo-ts\"><\/div><\/form><div class=\"rpo-status\" role=\"status\" aria-live=\"polite\"><\/div><div class=\"rpo-footer\"><p>Don't worry - I will only send you information about how to make your music sound amazing. I take this stuff seriously and will NEVER sell your info. You have my word \ud83d\udc4d<\/p><\/div><\/div><\/div>\n\n\n\n<h2 id=\"export-settings-for-mastering\" class=\"wp-block-heading\">What File Format, Bit Depth and Sample Rate Should I Export?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Export the mix in an uncompressed audio format.<\/strong> One of the most common mistakes I see is compressed (lossy) audio sent in for mastering: MP3, M4A, WMA and so on. Send a WAV or AIFF file instead. FLAC is lossless, so it works too. MP3s should only be submitted as a last resort!<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Lossy formats are popular because the files are small, but the reduction in file size happens because audio is thrown away. The data that gets removed is usually the frequencies that are hardest to hear, and the more a file is compressed, the more distortion and artifacts it has. Uncompressed and lossless files keep all of the audio information. You can <a href=\"https:\/\/www.raytownproductions.com\/blog\/mp3-wav-aac-best-settings\/\">hear what lossy encoding does<\/a> in my MP3 vs. WAV vs. AAC comparison.<\/p>\n\n\n\n<figure class=\"wp-block-table is-style-stripes rytbd-table\"><table><thead><tr><th>Setting<\/th><th>What to choose<\/th><th>Why<\/th><\/tr><\/thead><tbody><tr><td>File format<\/td><td>WAV or AIFF (FLAC also works)<\/td><td>Uncompressed or lossless, so nothing is thrown away.<\/td><\/tr><tr><td>Channels<\/td><td>One stereo file per song<\/td><td>Mastering works on the finished stereo mix.<\/td><\/tr><tr><td>Bit depth<\/td><td>The bit depth of your session: 24-bit is typical, 32-bit float is fine<\/td><td>Reducing the bit depth requires dither, which is the mastering engineer&#8217;s job.<\/td><\/tr><tr><td>Sample rate<\/td><td>The sample rate of your session (for example 44.1 or 48 kHz)<\/td><td>Converting up adds file size, not quality.<\/td><\/tr><tr><td>Peak level<\/td><td>Never over 0 dBFS; at least &#8722;3 dBFS of headroom, &#8722;6 dBFS is better<\/td><td>Clipped audio is distorted for good.<\/td><\/tr><tr><td>Master bus<\/td><td>Limiters and loudness plugins bypassed<\/td><td>Dynamic range can&#8217;t be put back once it&#8217;s gone.<\/td><\/tr><tr><td>Normalize and dither<\/td><td>Off<\/td><td>The file should arrive untouched, at the level you mixed it.<\/td><\/tr><tr><td>Start and end<\/td><td>About 5 seconds of silence before and after the song<\/td><td>No first note or reverb tail gets cut off.<\/td><\/tr><tr><td>Lossy formats<\/td><td>Avoid MP3, M4A and WMA<\/td><td>Last resort only.<\/td><\/tr><\/tbody><\/table><figcaption class=\"wp-element-caption\">Export settings for a mix going to mastering. Headroom, silence, normalization and dither settings are the ones in my services FAQ.<\/figcaption><\/figure>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-tip is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Pro tip: export the files in the same quality they were recorded in.<\/strong> If the song was recorded at 16-bit, 44.1 kHz, export the final mix at that bit depth and sample rate. Changing the bit depth requires dithering, which should be handled by the mastering engineer. Up-converting doesn&#8217;t add any new information either; it only makes the file larger. The same goes for lossy files. If you bought a beat from a producer and they gave you an MP3, converting it to WAV will not bring back the audio that was removed. Ask the producer for the WAV instead.<\/p>\n<\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Two smaller things about the start and end of the file. Don&#8217;t trim the bounce tight against the first note or the last one, because that&#8217;s how a breath or a reverb tail gets chopped. And if the song has a fade-out, I&#8217;d suggest leaving the fade off the mix and telling your mastering engineer where it should start and end. A fade that&#8217;s already in the file gets pushed through the mastering compressor and limiter, which changes how it sounds. If the fade is a creative part of the mix, send both versions.<\/p>\n\n\n\n<h2 id=\"name-and-organize-files\" class=\"wp-block-heading\">How Should I Name and Organize My Files?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Label your songs correctly and neatly!<\/strong> Naming your songs seems trivial, but an online mastering engineer can have two or three projects on the desk in a day, and tidy files make a real difference.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Start each file name with a two-digit track number:<\/strong> 01, 02, 03 and so on. That keeps the songs in the correct order on any computer.<\/li>\n\n\n\n<li><strong>Use the full, final song title.<\/strong> More often than not, song titles change once the songs are completely finished, so don&#8217;t forget to update the file names as well.<\/li>\n\n\n\n<li><strong>Spell it the way it should be released.<\/strong> The names you send are usually the names that end up in the final files.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">If the files aren&#8217;t labeled with the final titles, the mastering engineer has to spend time figuring out the actual song order and names. That costs you time and money in the end.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder.webp\" alt=\"File naming example for a 3-song EP: a list of unclear names such as final mix NEW v7.wav next to an organized Artist Name folder with a Mastering folder, a track info sheet and song folders numbered 01, 02 and 03, where the first song folder holds the mix, a reference file and notes\" class=\"wp-image-29625\" width=\"1600\" height=\"900\" srcset=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder.webp 1600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder-600x338.webp 600w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder-1024x576.webp 1024w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder-768x432.webp 768w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder-1536x864.webp 1536w, https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/2026\/11\/online-mastering-file-naming-and-song-folder-1080x608.webp 1080w\" sizes=\"(max-width: 1600px) 100vw, 1600px\" \/><figcaption class=\"wp-element-caption\">A good example of file naming and folder layout for a 3-song EP.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">For projects sent to me, I ask for one folder named after the artist, then one folder per service (for example &#8220;Mastering&#8221;), then one folder per song. Each song folder needs just three things:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>The mix to be mastered,<\/strong> named with the track number and final title.<\/li>\n\n\n\n<li><strong>A reference file,<\/strong> named the same with &#8220;-Reference&#8221; on the end. This is the best sound you were able to get out of the song with your own master bus processing. It shows me where you were heading.<\/li>\n\n\n\n<li><strong>Notes.<\/strong> Anything I should know about the song. This is also where you name songs or other mixes you want yours to sound like, if that&#8217;s helpful.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Zip the artist folder and send a link from Dropbox, WeTransfer, Google Drive or whichever file transfer service you like.<\/p>\n\n\n\n<h2 id=\"track-info-sheet-references-notes\" class=\"wp-block-heading\">What Information Should I Send With the Mix?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Include a track info sheet with any metadata you want encoded in your MP3s or DDP.<\/strong> Staying organized is crucial during mastering. The song and artist information gets encoded into the final files, and once those files are sent out, corrections are often impossible and costly.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">An info sheet puts everything about the release in one convenient document, which makes it very easy for the mastering engineer to encode the final masters properly. I made an editable one you can use: <a href=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/Blog\/8-Tips-Mastering\/Track_Info_Sheet.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">download my free track info sheet<\/a> and send it with your files. Your mastering engineer will thank you.<\/p>\n\n\n\n<figure class=\"wp-block-table is-style-stripes rytbd-table\"><table><thead><tr><th>Include<\/th><th>Details<\/th><\/tr><\/thead><tbody><tr><td>Artist and release<\/td><td>Artist name and the EP or album title, spelled exactly as they should appear.<\/td><\/tr><tr><td>Track list<\/td><td>Final running order and final song titles, matching the file names.<\/td><\/tr><tr><td>Codes<\/td><td>ISRC codes if you already have them, and a UPC or EAN for a CD. ISRCs come from your distributor or, in the United States, from the <a href=\"https:\/\/usisrc.org\/\" target=\"_blank\" rel=\"noreferrer noopener\">US ISRC Agency<\/a>.<\/td><\/tr><tr><td>Formats you need<\/td><td>Streaming and download masters, a DDP for CD replication, tagged MP3s, or a mix of these.<\/td><\/tr><tr><td>Credits and other tags<\/td><td>Songwriters, year, genre and anything else you want embedded.<\/td><\/tr><tr><td>Contact<\/td><td>Who to send the masters to, and who approves them.<\/td><\/tr><\/tbody><\/table><figcaption class=\"wp-element-caption\">What a track info sheet should cover. Ask your distributor or pressing plant which codes and formats they require.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The notes file in each song folder covers the rest:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>What to tell me.<\/strong> Keep it short. Tell me anything that is intentional and could look like a mistake (a distorted vocal, a lo-fi intro, a noisy amp you love), how you want the gaps and transitions between songs on an EP or album, and anything in the mix that still bothers you.<\/li>\n\n\n\n<li><strong>Songs or mixes to compare with.<\/strong> If it helps, name one or two released songs, or other mixes of yours, whose sound and loudness you like. A link is enough. They tell me more about the tone, low end and loudness you&#8217;re after than a paragraph of description can.<\/li>\n<\/ul>\n\n\n\n<div class=\"wp-block-group rytbd-callout rytbd-callout-note is-layout-flow wp-block-group-is-layout-flow\">\n<p class=\"wp-block-paragraph\"><strong>Need alternate versions?<\/strong> If you want an instrumental, a clean edit or a performance track mastered too, export those mixes from the same session with the same settings and send them together with the main mix. They can then be mastered to match. Ask about this before the project starts, since extra versions are extra work.<\/p>\n<\/div>\n\n\n\n<h2 id=\"revisions-and-what-you-get-back\" class=\"wp-block-heading\">What Happens After You Send Your Mix?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">With online mastering you aren&#8217;t in the room, so it helps to know how the rest of the process usually goes. Every engineer works a little differently, and the timing below is what I list in my own services FAQ.<\/p>\n\n\n\n<figure class=\"wp-block-table is-style-stripes rytbd-table\"><table><thead><tr><th>Step<\/th><th>What happens<\/th><th>Your part<\/th><\/tr><\/thead><tbody><tr><td>1.&nbsp;Check-in<\/td><td>The engineer loads your files and checks format, levels and anything that looks like a problem.<\/td><td>Answer questions quickly. If there&#8217;s a real issue, you may be asked for a new mix.<\/td><\/tr><tr><td>2.&nbsp;First&nbsp;master<\/td><td>Mastering takes me about 1&#8211;3 days for a song and under 5 days for most albums.<\/td><td>Wait for the first version before sending more notes.<\/td><\/tr><tr><td>3.&nbsp;Listening<\/td><td>You get the master to review.<\/td><td>Listen on several systems and compare it with your mix at the same volume.<\/td><\/tr><tr><td>4.&nbsp;Revisions<\/td><td>For 10 days after the first version, I revise the master for free until it&#8217;s right.<\/td><td>Send one clear list of notes, with times.<\/td><\/tr><tr><td>5.&nbsp;Final&nbsp;files<\/td><td>The approved master is exported in the formats you asked for, with your metadata.<\/td><td>Check titles, order and spelling before you upload or press anything.<\/td><\/tr><\/tbody><\/table><figcaption class=\"wp-element-caption\">A typical online mastering job from upload to final files. Turnaround and revision terms are the ones listed in my services FAQ; other engineers will differ.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">A few habits make the revision stage short and painless:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Match the volume before you judge.<\/strong> The master will be much louder than your mix, and louder almost always sounds better at first. Turn the master down until it&#8217;s as loud as the mix, then compare tone, punch and width.<\/li>\n\n\n\n<li><strong>Listen where you normally listen.<\/strong> Car, earbuds, phone speaker, your studio monitors. Take notes with the time of each spot you want changed.<\/li>\n\n\n\n<li><strong>Send one consolidated list.<\/strong> If you&#8217;re in a band, agree on the notes first. One message with everything in it gets you a better revision than five messages that contradict each other. I go deeper on this in <a href=\"https:\/\/www.raytownproductions.com\/blog\/get-better-mixes-faster-effective-communication-remote-mixing-mastering-part-2\/\">how to write the best mix notes<\/a>.<\/li>\n\n\n\n<li><strong>Know what&#8217;s a mastering note and what&#8217;s a mix note.<\/strong> &#8220;A little brighter&#8221;, &#8220;less low end&#8221;, &#8220;louder&#8221; and &#8220;more space between songs&#8221; are mastering notes. &#8220;Turn the vocal up&#8221; or &#8220;the snare is too loud&#8221; are mix notes. A mastering engineer has limited ways to change one instrument inside a stereo file, so the best fix is usually a revised mix. Export it with exactly the same settings and add a version number to the file name.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">What comes back depends on where the music is going: WAV masters for your distributor, a DDP if you&#8217;re pressing CDs, and tagged MP3s for promo. Tell your engineer up front which of those you need.<\/p>\n\n\n\n<h2 id=\"closing-thoughts\" class=\"wp-block-heading\">Closing Thoughts<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">To quickly summarize: don&#8217;t paint your mastering engineer into a corner by reducing the dynamics or adding EQ and effects on the main output bus. Export your files in the highest quality they were recorded at (up-converting doesn&#8217;t help!). Name your song files with their track number and final title. And if possible, supply a track info sheet with all of the album metadata on it for encoding.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you&#8217;re getting ready to release something and have questions about your mix, <a href=\"https:\/\/www.raytownproductions.com\/#contact\">send me a message<\/a> and tell me about the project.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">How have you been submitting your songs for mastering? Tell me in the comments below!<\/p>\n\n\n\n<div class=\"wp-block-group rytbd-affiliates is-layout-flow wp-block-group-is-layout-flow\">\n<h2 class=\"wp-block-heading\">Free Downloads Mentioned<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"https:\/\/www.raytownproductions.com\/blog\/wp-content\/uploads\/Blog\/8-Tips-Mastering\/Track_Info_Sheet.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">My free track info sheet (PDF)<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/tiny.cc\/rp-mastering-sheets\" target=\"_blank\" rel=\"noreferrer noopener\">My FREE mastering cheat sheets<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.raytownproductions.com\/plugins\/hardstop\/\" target=\"_blank\" rel=\"noreferrer noopener\">HardStop: my clean, anti-aliased clipper (Basic is free)<\/a><\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><em>The info sheet is a direct download. The cheat sheets are free in exchange for your email address.<\/em><\/p>\n<\/div>\n\n\n\n<div class=\"wp-block-group rytbd-takeaways is-layout-flow wp-block-group-is-layout-flow\">\n<h2 class=\"wp-block-heading\">Key takeaways<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Send a finished mix.<\/strong> Fix clicks, pops and unwanted noise in the session, then listen to the exported file from start to finish.<\/li>\n\n\n\n<li><strong>Bypass loudness processing and dither.<\/strong> Limiters, maximizers and dither come off the master bus. Keep a compressor, EQ or effect only if it&#8217;s a necessary part of the sound, or send both versions.<\/li>\n\n\n\n<li><strong>Never go over 0 dBFS.<\/strong> At least &#8722;3 dBFS of headroom, and &#8722;6 dBFS is better. It&#8217;s a starting point, not an exact target.<\/li>\n\n\n\n<li><strong>Export WAV or AIFF at recorded quality.<\/strong> Same sample rate and bit depth as the session, no normalization, no up-converting and no MP3s.<\/li>\n\n\n\n<li><strong>Label and document.<\/strong> Two-digit track numbers, final song titles, a track info sheet, reference songs and short notes.<\/li>\n\n\n\n<li><strong>Review the master at matched volume<\/strong> and send one clear list of revision notes.<\/li>\n<\/ul>\n<\/div>\n\n\n\n<div class=\"wp-block-group rytbd-faq is-layout-flow wp-block-group-is-layout-flow\">\n<h2 class=\"wp-block-heading\">Frequently asked questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">How much headroom should I leave for mastering?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The hard rule is that the mix never goes over 0 dBFS. For songs sent to me, I ask for at least -3 dBFS of headroom, and -6 dBFS is better. You don&#8217;t need to hit an exact number. A mix that peaks at -4 or -8 dBFS is fine, as long as nothing clips and there is no limiter on the master bus.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Should I take the limiter off my mix before mastering?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Yes. Bypass limiters, maximizers and any clipper you added only for loudness. They reduce the dynamic range, and once it is gone it is very difficult, if not impossible, to bring back. If a compressor, EQ or effect on the master bus is a necessary part of the sound, leave it on, or send two versions: one with it and one without.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Should I dither my mix before sending it to mastering?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. Turn dither off, including the dither built into some limiter plugins. Dither is meant to be applied once, at the very end, when the bit depth is reduced for the final format. Export at the bit depth of your session and let the mastering engineer handle it.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What file format should I send for mastering?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Send an uncompressed stereo WAV or AIFF file at the sample rate and bit depth you recorded and mixed at. 24-bit is typical, and 32-bit float works too. FLAC is lossless, so it is fine as well. Avoid MP3, M4A and WMA unless there is no other option, and don&#8217;t convert a file to a higher sample rate or bit depth, because that adds file size, not quality.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can I send an MP3 for mastering?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Only as a last resort. An MP3 has already thrown away part of the audio to make the file smaller, and converting it back to WAV does not restore what was removed. Mastering brings out detail, so the artifacts of lossy encoding can become easier to hear. If an MP3 is truly all you have, send the highest-quality one and tell the engineer.<\/p>\n<\/div>\n\n\n\n<div class=\"wp-block-group rytbd-services-cta is-layout-constrained wp-block-group-is-layout-constrained\">\n<h3 class=\"wp-block-heading has-text-align-center\">Ready to Have Your Songs Mastered?<\/h3>\n\n\n\n<p class=\"has-text-align-center wp-block-paragraph\">I mix and master songs for independent artists, bands and producers. Tell me about your release, send your prepared mixes, and I&#8217;ll make them loud, punchy and ready for every platform. Or learn to do it yourself in my courses.<\/p>\n\n\n\n<div class=\"wp-block-buttons is-content-justification-center is-layout-flex wp-container-core-buttons-is-layout-fe48e5de wp-block-buttons-is-layout-flex\">\n<div class=\"wp-block-button\"><a class=\"wp-block-button__link wp-element-button\" href=\"https:\/\/www.raytownproductions.com\/#services\">Get Your Song Mixed &amp; Mastered<\/a><\/div>\n\n\n\n<div class=\"wp-block-button is-style-outline is-style-outline--1\"><a class=\"wp-block-button__link wp-element-button\" href=\"https:\/\/academy.raytownproductions.com\/\" target=\"_blank\" rel=\"noopener\">Learn in My Courses<\/a><\/div>\n<\/div>\n<\/div>\n\n\n\n<script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"url\": \"https:\/\/www.raytownproductions.com\/blog\/8-tips-to-get-the-most-from-online-song-mastering\/\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"How much headroom should I leave for mastering?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The hard rule is that the mix never goes over 0 dBFS. For songs sent to me, I ask for at least -3 dBFS of headroom, and -6 dBFS is better. You don't need to hit an exact number. A mix that peaks at -4 or -8 dBFS is fine, as long as nothing clips and there is no limiter on the master bus.\"}}, {\"@type\": \"Question\", \"name\": \"Should I take the limiter off my mix before mastering?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Yes. Bypass limiters, maximizers and any clipper you added only for loudness. They reduce the dynamic range, and once it is gone it is very difficult, if not impossible, to bring back. If a compressor, EQ or effect on the master bus is a necessary part of the sound, leave it on, or send two versions: one with it and one without.\"}}, {\"@type\": \"Question\", \"name\": \"Should I dither my mix before sending it to mastering?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Turn dither off, including the dither built into some limiter plugins. Dither is meant to be applied once, at the very end, when the bit depth is reduced for the final format. Export at the bit depth of your session and let the mastering engineer handle it.\"}}, {\"@type\": \"Question\", \"name\": \"What file format should I send for mastering?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Send an uncompressed stereo WAV or AIFF file at the sample rate and bit depth you recorded and mixed at. 24-bit is typical, and 32-bit float works too. FLAC is lossless, so it is fine as well. Avoid MP3, M4A and WMA unless there is no other option, and don't convert a file to a higher sample rate or bit depth, because that adds file size, not quality.\"}}, {\"@type\": \"Question\", \"name\": \"Can I send an MP3 for mastering?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Only as a last resort. An MP3 has already thrown away part of the audio to make the file smaller, and converting it back to WAV does not restore what was removed. Mastering brings out detail, so the artifacts of lossy encoding can become easier to hear. If an MP3 is truly all you have, send the highest-quality one and tell the engineer.\"}}]}<\/script>\n","protected":false},"excerpt":{"rendered":"<p>Eight tips for sending a finished mix to an online mastering engineer: bypass the limiter and dither, leave headroom, clean up clicks and noise, export a WAV at the quality you recorded, name the files with their track numbers and final titles, and include an info sheet, references and notes.<\/p>\n","protected":false},"author":1,"featured_media":29637,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[2],"tags":[47,39,43,21,22],"class_list":["post-25826","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-tips-tricks","tag-dithering","tag-mastering","tag-preparing","tag-tips","tag-tricks","et-has-post-format-content","et_post_format-et-post-format-standard"],"_links":{"self":[{"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/posts\/25826","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/comments?post=25826"}],"version-history":[{"count":24,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/posts\/25826\/revisions"}],"predecessor-version":[{"id":29626,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/posts\/25826\/revisions\/29626"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/media\/29637"}],"wp:attachment":[{"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/media?parent=25826"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/categories?post=25826"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.raytownproductions.com\/blog\/wp-json\/wp\/v2\/tags?post=25826"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}